Search Results

Overview Clean out any debris from the filter box underneath the machine Put in a tool report + Asana task to change the filter if it looks dirty. Procedure Setup Wear a dust mask Locate the jewelry area shop vac and bring it to the polishing...

Service manual: https://drive.google.com/file/d/17N-GZd98lkBZe_qzui03i1omQ-WQyV2a/view Clean and Lubricate Wipe off or vacuum the accumulated debris and dust. Lubricate the arbor press ram with a light machine oil. Check and Service Ram Check the ram ...

Lubricate conveyor table leadscrews and sprockets. (fig 3) Clean the leadscrews, chain, and sprockets with a soft wire brush. Apply 1–2 pumps of grease from a grease gun onto the sprockets and leadscrew threads. Adjust the conveyor up or down to spread...

Lubricate conveyor roller bushings with a couple drops of 3-in-1 oil from a can (located in Maintenance Cart drawer) in holes(fig 1). The manual says this should be done daily—since we do not see daily use, weekly should be OK Avoid adding too much oil...

Underneath the Rabbit lasers there's a cabinet, containing a box that collects any small pieces of material that fall through the honeycomb. Clean the Catch Boxes For each of the large format lasers: 1. Unlatch and open the bottom panel in the front of the m...

This needs to be reviewed for content and tech_ready suitability before it is approved to be scheduled maintenance Remove the bed and clean up the material that has fallen though. Use a poking tool to free all of the material stuck in the honeycomb. Acqui...

(Link to PDF Tool Tutorial) Pressures and Regulators ⛔ Do not adjust pressures of regulators or the air compressor. Start a conversation on Discord or file a maintenance request if you have a need not addressed below. There is a regulator manifold on the ou...

Horizontal Band Saw The horizontal Band Saw is a liquid cooled, fairly accurate saw capable of cutting mild steel, aluminum and other non-ferrous metals. The horizontal Band Saw is different from a vertical band saw in that your material stays stationary whil...

(Link to PDF Tool Tutorial) Requirements Brad Nailer can be used without a clearance. Warnings 🚫 Never connect to an air source that is capable of exceeding 200 PSI.🚫 Do not fire fastener on top of another fastener, into surfaces too hard to penetrate, or ...

Overview The teleconferencing equipment in the conference room consists of: A rolling stand with a TV A linux-based controller box that runs Zoom (other software maybe installed if needed) A wide-angle camera (located on top of the TV) An EMEET speaker/...

Cold Saw The cold saw makes accurate, square and angled cuts in steel and aluminum. The saw is heavy and stable and the dual vise clamping system makes for more accurate cuts than an abrasive chop saw with minimal burring, almost like a machined edge. It uses...

Introduction The Evolution S355MCS Mitre Saw is a powerful tool designed for cutting various materials, including mild steel, and aluminum.  Notes Safety Read and understand the instructions. Before operating the saw, thoroughly read the instruction manu...

(Link to PDF Tool Tutorial) Narrow crown construction staplers are used for cabinets, casebacks, drawers, insulation sheathing, underlayment, molding and trim. Unlike larger staplers designed to go around cables or wire without penetrating, a narrow crown sta...

(Link to PDF Tool Tutorial) Requirements General Metal Working clearance or class equivalent is required before use. Warnings 🚫 Do not stand on the machine. Serious injury could occur if the machine tips over. Do not wet grind or polish. 🚫 Never use...

(Link to PDF Tool Tutorial) Finishing nail guns are powerful tools that can handle basic home improvement tasks as well as professional jobs. Use finishing nailers (also known as trim nail guns) to complete flooring and molding projects without one swing of a...

Link to PDF Tool Tutorial: letter size walking foot 2025.pdf Link to PDF Tool Poster:  TODO: factor out content shared with Industrial Straight Stitch This machine is intended for use on heavy materials like vinyl, leather and heavy layers of upholstery. Th...

Morgan Industries G-100T Injection Molding Machine The injection-molding machine forms plastic parts by melting plastic and forcing the plastic into a multi-plate mold that is held in a powerful clamp. After the plastic solidifies, the clamp is released, allo...

Wood Lathe A wood lathe is a machine that rotates a piece of wood on an axis and allows the operator to shape it with various cutting tools. Wood lathes are used for making furniture, bowls, musical instruments and other objects. However, working with a wood ...

(Link to PDF Tool Tutorial) The magnetic tumbler uses tiny metal pins driven by a powerful rotating magnet to polish and work-harden pieces. The Tool Safety, Tool Care, Operation, section of this guide are what instructors use to ensure that you can use the ...

JET Vertical Mill Loose clothing should not be worn around the mill. ABSOLUTELY NO GLOVES may be worn while operating the mill: this includes latex, nitrile, vinyl, and similar gloves. Any jewelry on the hands or wrists must taken off while using the mill. Lo...