Search Results

Overview Clean the cutter head. Check cutter blades for chips and dullness. Generally inspect the machine for damage and loose or worn parts. Check the dust extraction for blockages. Procedure Setup Grab the maintenance cart. Unplug the planer. ...

Overview Clean out any debris from the filter box underneath the machine Put in a tool report + Asana task to change the filter if it looks dirty. Procedure Setup Wear a dust mask Locate the jewelry area shop vac and bring it to the polishing...

Wiki page: https://protohaven.org/wiki/tools/air_compressor#maintenance_schedule Service manual: https://drive.google.com/file/d/1XzDx7dxhe-dacSaEM6lDuwz62_uSK6YC/view Task List Wear safety glasses and hearing protection Check for proper oil level (withi...

Service manual: https://drive.google.com/file/d/17N-GZd98lkBZe_qzui03i1omQ-WQyV2a/view Clean and Lubricate Wipe off or vacuum the accumulated debris and dust. Lubricate the arbor press ram with a light machine oil. Check and Service Ram Check the ram ...

Lubricate conveyor table leadscrews and sprockets. (fig 3) Clean the leadscrews, chain, and sprockets with a soft wire brush. Apply 1–2 pumps of grease from a grease gun onto the sprockets and leadscrew threads. Adjust the conveyor up or down to spread...

Perform weekly maintenance Remove the lower panel on the infeed side of the machine. Vacuum dust buildup from inside cabinet and off motor. Check v-belts for damage, tension, and wear. Yellow/Red tag the machine if issues are observed.  Check for problema...

Lubricate conveyor roller bushings with a couple drops of 3-in-1 oil from a can (located in Maintenance Cart drawer) in holes(fig 1). The manual says this should be done daily—since we do not see daily use, weekly should be OK Avoid adding too much oil...

Underneath the Rabbit lasers there's a cabinet, containing a box that collects any small pieces of material that fall through the honeycomb. Clean the Catch Boxes For each of the large format lasers: 1. Unlatch and open the bottom panel in the front of the m...

Safety Wear glovesWear safety glassesWear a dust mask Clean Bed 1. Remove the honeycomb bed. 2. Clean up and discard any material that has fallen though the bed.3. Use a poking tool to free all of the material stuck in the honeycomb. Clean up and discard ma...

1. Reserve each laser one at a time to ensure they're not both down at the same time. 2. Remove the blower from the system and loosen any large debris on the slots on the blower cage with a flathead screwdriver, then brush clean with a bristle brush. Be carefu...

This needs to be reviewed for content and tech_ready suitability before it is approved to be scheduled maintenance Remove the bed and clean up the material that has fallen though. Use a poking tool to free all of the material stuck in the honeycomb. Acqui...

(Link to PDF Tutorial) Warnings 🚫Do not use unapproved filaments at Protohaven. It could lead to damage to the printer or emit particles or fumes irritating to people working in the studio. 🚫Do not use metal tools on the build sheet. There are plastic scrap...

(Link to PDF Tool Tutorial) Pressures and Regulators ⛔ Do not adjust pressures of regulators or the air compressor. Start a conversation on Discord or file a maintenance request if you have a need not addressed below. There is a regulator manifold on the ou...

Horizontal Band Saw The horizontal Band Saw is a liquid cooled, fairly accurate saw capable of cutting mild steel, aluminum and other non-ferrous metals. The horizontal Band Saw is different from a vertical band saw in that your material stays stationary whil...

Jet 1610 Vertical Metal Bandsaw – Safety & Operation Overview Before operating the bandsaw, ensure you've read the operator’s manual thoroughly. Make sure the machine is stable and all guards are securely in place. Inspect the blade for wear  Wear safety gla...

(Link to PDF Tool Tutorial) Usage Highlights Safety Care Cleanup —————————————————- ———————————————————————————————————— ——————————————— 1. Keep materials flat to the table 1. Use the entire width of the abrasive belt 1. Brush t...

(Link to PDF Tool Tutorial) Requirements Brad Nailer can be used without a clearance. Warnings 🚫 Never connect to an air source that is capable of exceeding 200 PSI.🚫 Do not fire fastener on top of another fastener, into surfaces too hard to penetrate, or ...

(Link to PDF Tool Tutorial)

(Link to PDF Tool Tutorial) Personal Protective Equipment Standard shop personal protective equipment (safety glasses, no long hair, no flowing clothes, etc.) are required ABSOLUTELY NO gloves, rings, bracelets, or other items on your hands or finge...

CNC Metal Mill (Tormach 770) The Tormach can cut a diverse range of materials from aluminum, brass, copper and Delrin. Steels can be cut but are tricky because of machine flex.  A mill is used to machine surfaces, cut slots and pockets, and drill holes to pr...