Search Results

Service manual: PENDING*Inspect the Blade*Inspect the saw blade for wear and damage.1. If any teeth are missing, yellow tag the tool in a tool report and file a purchase request if there are no spares in the maintenance room.1. If two consecutive teeth are mis...

CNC Wood Router (Avid Pro 60x120) The Avid CNC router is used to run cutting and milling operations on various materials such as wood, plastic, and aluminum. The most common use is to use it to engrave and cut shapes out of plywood or hardwood. But the machin...

*Materials*For a disinfectant, you can use sanitizing spray (kept under the kitchen sink, with refills in the maintenance closet)Apply disinfectant, wait three minutes, then wipe with a clean cloth or paper towel.If we are out of disindectant, submit a purchas...

*Compare Online and Physical Tool States*1. Open https://api.protohaven.org/techs 2. Make a note of tools in a yellow or red state.3. Visit each of the tools listed as red or yellow state and verify that there is a physical tag on the tool that matches that st...

*Recharge Desiccant Pack* 1. Remove the white rectangular plastic desiccant pack from the "free filament" tote box by the 3D printing cabinet.2. Inspect the desiccant beads through the front window.3. Use the legend by the window to gauge if the beads are wet...

Manual Metal Lathe The lathe is used to make parts with radial symmetry and can be used to make incredibly precise cuts in most metals and plastics (accurate to the .001 inch!). It is a joy to operate, but it must command your full attention. Never leave the...

Test the PH of the water Locate the PH test strips, in the computer cubby hole at the CNC Plasma Computer station.   Use a stick or other object to lightly stir the water in the table. Just lightly move the water in between the slats, careful not to splash...

*Gloves*Inspect gloves. Put in a purchase request for any pairs that have holes or excessive wear (don't throw them out until we have replacements) - Purchase request: https://protohaven.org/purchasing*Helmets* 1. Make a purchase request if the helmet is nonfu...

Place a post it note or tape a slip of paper with the current date on all of packages that are on the shelf.  Look for older packages that have been there for a week or more and move them to the lost/found shelf in Camden's office.  Important: Email Camden...

"Empty the Media Separator Drawer Behind the Plasma table is a square gray machine that is the media separator for the sand blaster. There is a drawer on the bottom with two retaining latches. Put on a dust mask and safety glasses  Ensure the sandblaster...

If the popcorn maker is already clean, you can just close out this task. *Clean Out Popcorn Compartment*1. Unplug the popcorn maker.1. Remove any stale popcorn already in the popcorn maker. *Clean the Kettle* 1. Unplug the kettle.2. Lift the kettle up and o...

Service manual: https://drive.google.com/file/d/16HFrtwBzy-s0uS8aojnePJ2yyeupkZX2/view?usp=drive_link Unplug before cleaning. The miter saw should be cleaned with vacuum or a dry rag as needed to keep free of dust. Yellow plastic panel on work surface shoul...

The pantograph is a tool that's especially useful for engraving - maker's marks etc. It uses a template and a 1.5x-10x reduction linkage to achieve very precise motion over a very small space without the aid of a CNC machine. Basic Info This machine has tw...

Weekly Welding Table Maintenance (Mig and Tig tables) Wipe table down with a dry rag.  Inspect the table for spatter/BBs. Use a straight edge to assist in finding them. If tables have not seen much use, looks to be free from BBs and still has a good coatin...

*Safety*- Wear a dust mask.- Wear safety glasses.*Task List*To wipe down oven surfaces, use a clean shop rag and a mixture of water with a little soap. Just lightly damp, not dripping wet. (Do not use solvent-based cleaners, as they can affect the powder cure....

*Safety* - Wear a dust mask. (If you do not have your own, disposable masks are available in the custodial room.)- Wear safety glasses. *Empty Shop Vacs and Service Filters* We have 11 shop vacs - two in precision metals (one for dry, one for wet), one at t...

Clean/Lubricate the  X/Y/Z Axis of the 3d printers Grab the cleaning kit. Located on the shelf in the 3d printer cabinet.  Use the Z Axis cleaning device in the kit. If a replacement is needed: https://www.printables.com/model/229145-z-axis-screw-cleaning-...