Search Results

Overview Clean out any debris from the filter box underneath the machine Put in a tool report + Asana task to change the filter if it looks dirty. Procedure Setup Wear a dust mask Locate the jewelry area shop vac and bring it to the polishing...

Service manual: https://drive.google.com/file/d/17N-GZd98lkBZe_qzui03i1omQ-WQyV2a/view Clean and Lubricate Wipe off or vacuum the accumulated debris and dust. Lubricate the arbor press ram with a light machine oil. Check and Service Ram Check the ram ...

Fire extinguishers are located in the following areas: Kitchen Wood Shop Maintenance Room Blacksmithing  Front Entrance For each fire extinguisher: Verify that all fire extinguishers are pressurized (indicator is in the green range).  Verify that...

Lubricate conveyor table leadscrews and sprockets. (fig 3) Clean the leadscrews, chain, and sprockets with a soft wire brush. Apply 1–2 pumps of grease from a grease gun onto the sprockets and leadscrew threads. Adjust the conveyor up or down to spread...

Lubricate conveyor roller bushings with a couple drops of 3-in-1 oil from a can (located in Maintenance Cart drawer) in holes(fig 1). The manual says this should be done daily—since we do not see daily use, weekly should be OK Avoid adding too much oil...

Underneath the Rabbit lasers there's a cabinet, containing a box that collects any small pieces of material that fall through the honeycomb. Clean the Catch Boxes For each of the large format lasers: 1. Unlatch and open the bottom panel in the front of the m...

This needs to be reviewed for content and tech_ready suitability before it is approved to be scheduled maintenance Remove the bed and clean up the material that has fallen though. Use a poking tool to free all of the material stuck in the honeycomb. Acqui...

Clean the Interior Open the side panel. Dredge out any buildup of chips, gunk, and other debris. Ensure the cutting fluid can make its way to the sight glass on the bottom right of the machine. If it's not visible, submit a maintenance request so a traine...

Perform weekly maintenance Remove the lower panel on the infeed side of the machine. Vacuum dust buildup from inside cabinet and off motor. Check v-belts for damage, tension, and wear. Yellow/Red tag the machine if issues are observed.  Check for problema...

Test the PH of the water Locate the PH test strips, in the computer cubby hole at the CNC Plasma Computer station.   Use a stick or other object to lightly stir the water in the table. Just lightly move the water in between the slats, careful not to splash...

Check the inventory for the first aid kits. Restock any low supplies; backstock is stored in Custodial. Submit purchase requests if anything is needed - especially bandages as they disappear quickly. There are three first aid kits - one each in the Kitchen, W...

Place a post it note or tape a slip of paper with the current date on all of packages that are on the shelf.  Look for older packages that have been there for a week or more and move them to the lost/found shelf in Camden's office.  Important: Email Camden...

Enter the password followed by # and ensure the light on the front of the box is green (i.e. good battery). If you see any other color, replace the batteries (4x AA). The password is present in Vaultwarden - accessible via the Chrome browser extension on the ...

Overview Clean the cutter head. Check cutter blades for chips and dullness. Wax the bed Generally inspect the machine for damage and loose or worn parts. Check the dust extraction for blockages. Procedure Setup Grab the maintenance cart. Rotate ...

Recharge Desiccant Pack Remove the white rectangular plastic desiccant pack from the "free filament" tote box by the 3D printing cabinet. Inspect the desiccant beads through the front window. Use the legend by the window to gauge if the beads are wet. If...

Clean/Lubricate the  X/Y/Z Axis of the 3d printers Grab the cleaning kit. Located on the shelf in the 3d printer cabinet.  Use the Z Axis cleaning device in the kit. If a replacement is needed: https://www.printables.com/model/229145-z-axis-screw-cleaning-...

Safety Wear a dust mask. (If you do not have your own, disposable masks are available in the custodial room.) Wear safety glasses. Tools/Materials Required Two 2-gal buckets (should be located near the machine) Soft mallet. Clean Siphon Tube R...

Reserve each laser one at a time to ensure they're not both down at the same time.  Remove the blower from the system and loosen any large debris on the slots on the blower cage with a flathead screwdriver, then brush clean with a bristle brush. Be careful ...

Service manual - https://drive.google.com/file/d/10XyBZ8bd7pk9Vfl4iO3T76M2VwWSfi9C/view Safety Wear a dust mask. Wear safety glasses. Inspect/Rotate Nozzle Unplug the sandblaster Find a 1/8" Allen key in the maintenance cart. Unlock the carbide no...

The pantograph needs occasional oiling. We use the way oil from the manual metal lathe that is in the black bottle on the lathe. 2 pumps of oil in each spot of the pantograph is sufficient.      There are many places to oil the machine, there are ball oil...