Search Results

*Safety* - Wear a dust mask.- Wear safety glasses.- Unplug all electrical equipment before cleaning. *Task List* With a damp cloth, wipe down all external surfaces of the sheet metal tools:  - shear- slip roller- finger brake- shrinker/stretcher- turret pu...

The carbon monoxide detector is a small white plastic device located on the interior wall of the custodial room just to the right of the door.*Test CO Detector*- Push the test button on the carbon monoxide detector. - If it doesn't beep, the batteries are like...

*Safety* - Wear a dust mask. (If you do not have your own, disposable masks are available in the custodial room.)- Wear safety glasses. *Empty Shop Vacs and Service Filters* We have seven shop vacs - two in precision metals (one for dry, one for wet), one a...

* Woodshop* In the woodshop free bin and the free board caddy in the lathe area, remove any wood that: - Is painted or treated- Has nails/metal inside- Is heavily splintered- Is "swiss-cheesed" with little material to use, etc. *Metalshop* In the metalshop...

*Gloves*Inspect gloves. Put in a purchase request for any pairs that have holes or excessive wear (don't throw them out until we have replacements) - Purchase request: https://protohaven.org/purchasing*Helmets* 1. Make a purchase request if the helmet is nonfu...

Service manual: https://drive.google.com/file/d/1XsSwghnqBvr8uQD0qm1M8jcJ__te2DI1/view?usp=drive_link*Clean Dust and Debris*- Use pressurized air from the air compressor to blow out dust from around the electric motor and vfd, under the banjo and tailstock. - ...

*Safety* - Turn on the woodshop dust collection.- Wear a dust mask. (If you do not have your own, disposable masks are available in the custodial room.)- Wear hearing protection. (The dust collection is loud.) *Task List* For each woodshop tool:  - Use a s...

*Compare Online and Physical Tool States*1. Open https://api.protohaven.org/techs 2. Make a note of tools in a yellow or red state.3. Visit each of the tools listed as red or yellow state and verify that there is a physical tag on the tool that matches that st...

Service manual: https://drive.google.com/file/d/1QgkvdwpKXrfAl8W_3rSlNlg2mLRIDCh6/view*Task List*1. Check the spacing between the tool rests and the grinding wheels. (The spacing should be less than 1/16 of an inch, never more than 1/8 Inch.)2. Adjust the tool...

*Task List* 1. Use a shop vac, dust brush, or water-dampened paper towel to remove dust from all visible surfaces. (Pay special attention to the central table and the L-shaped table with finishing tools.)2. Wipe down the interior of the flame cabinet with a w...

*Safety* - Wear a dust mask. - Wear safety glasses. *Task List* DO NOT dust the interior of the forges as improper cleaning may damage the refractory material. 1. Use a shop vac or dust brush to remove dust from all visible surfaces, paying special attenti...

Service manual: https://drive.google.com/file/d/1YgGuXN2GB-ZQffNzAmpv5Zo6hYNJFlxi/view?usp=drive_link*Task List*- With a thumb or cloth, check for grease on the shaft of the upper blade guide and no accumulated debris. Reapply with grease from the grease gun i...

For each tool in the studio: - Use a shop vac or dust brush to remove dust from all visible surfaces.- Sweep the floor of the studio.- Dispose of any debris using the rolling trash cans.  

In the Custodial Room (behind the Jewelry Area) there is a bucket labeled "Leak Catcher" under a water pipe on the left side of the room as you enter. - If the bucket is more than half full, dump the water into the sink and return it to its position under the...

*Task List* - Organize all hand tools. (Put similar tools close to each other and ensure power cables are nicely stowed.)- Place any loose papers on the front desk in the desk organizer on the left hand side of the desk. Notify the #techs channel on Discord o...

If the popcorn maker is already clean, you can just close out this task. *Clean Out Popcorn Compartment*1. Unplug the popcorn maker.1. Remove any stale popcorn already in the popcorn maker. *Clean the Kettle* 1. Unplug the kettle.2. Lift the kettle up and o...

*Safety* - Wear a dust mask (if you do not have your own, disposable masks are available in the custodial room). *Task List* For each metal shop tool: 1. Use a shop vac or dust brush to remove dust from all visible surfaces. 2. Sweep the floors of the gene...

*Recharge Dessicant Pack* 1. Remove the white rectangular plastic dessicant pack from the "free filament" tote box by the 3D printing cabinet.2. Inspect the dessicant beads through the front window.3. Use the legend by the window to gauge if the beads are wet...

Service manual - https://drive.google.com/file/d/10XyBZ8bd7pk9Vfl4iO3T76M2VwWSfi9C/view*Safety*- Wear a dust mask.- Wear safety glasses.*Rotate Nozzle*1. Unplug the sandblaster1. Find a 1/8" Allen key in the maintenance cart.1. Unlock the carbide nozzle at the...

*Materials*For a disinfectant, you can use:- Sanitizing wipes (kept in the maintenance closet)- Sanitizing spray (kept under the kitchen sink, with refills in the maintenance closet)- AlcoholApply disinfectant, wait three minutes, then wipe with a clean cloth ...