Search Results

Overview Clean the cutter head. Check cutter blades for chips and dullness. Generally inspect the machine for damage and loose or worn parts. Check the dust extraction for blockages. Procedure Setup Grab the maintenance cart. Unplug the planer. ...

Overview Clean out any debris from the filter box underneath the machine Put in a tool report + Asana task to change the filter if it looks dirty. Procedure Setup Wear a dust mask Locate the jewelry area shop vac and bring it to the polishing...

Check for Storage Violations Open any lockers without storage tags and look for any materials stored there. Examine all board/bar and sheet storage for items stored without storage tags. Check for any cages with stored items that are also missing a storag...

Wiki page: https://protohaven.org/wiki/tools/air_compressor#maintenance_schedule Service manual: https://drive.google.com/file/d/1XzDx7dxhe-dacSaEM6lDuwz62_uSK6YC/view Task List Wear safety glasses and hearing protection Check for proper oil level (withi...

Service manual: https://drive.google.com/file/d/17N-GZd98lkBZe_qzui03i1omQ-WQyV2a/view Clean and Lubricate Wipe off or vacuum the accumulated debris and dust. Lubricate the arbor press ram with a light machine oil. Check and Service Ram Check the ram ...

Fire extinguishers are located in the following areas: Kitchen Wood Shop Maintenance Room Blacksmithing  Front Entrance For each fire extinguisher: Verify that all fire extinguishers are pressurized (indicator is in the green range).  Verify that...

Check the inventory for the first aid kits and submit purchase requests if anything is needed - especially bandages as they disappear quickly. There are three first aid kits - one each in the Kitchen, Woodshop, and Forge. Purchase request: https://protohaven...

Check all electrical outlets on ceiling drops and floor runs for loose outlets and/or cable clamps, improper use of "punch-out" junction boxes, or improper use of "power strips" not installed and used in accordance with instructions included in the listing, la...

Flush the Eyewash Station Run the eyewash station for  1-3 minutes. (This flushes any stagnant water from the line.)   

Lubricate conveyor table leadscrews and sprockets. (fig 3) Clean the leadscrews, chain, and sprockets with a soft wire brush. Apply 1–2 pumps of grease from a grease gun onto the sprockets and leadscrew threads. Adjust the conveyor up or down to spread...

Perform weekly maintenance Remove the lower panel on the infeed side of the machine. Vacuum dust buildup from inside cabinet and off motor. Check v-belts for damage, tension, and wear. Yellow/Red tag the machine if issues are observed.  Check for problema...

Lubricate conveyor roller bushings with a couple drops of 3-in-1 oil from a can (located in Maintenance Cart drawer) in holes(fig 1). The manual says this should be done daily—since we do not see daily use, weekly should be OK Avoid adding too much oil...

Underneath the Rabbit lasers there's a cabinet, containing a box that collects any small pieces of material that fall through the honeycomb. Clean the Catch Boxes For each of the large format lasers: 1. Unlatch and open the bottom panel in the front of the m...

Safety Wear glovesWear safety glassesWear a dust mask Clean Bed 1. Remove the honeycomb bed. 2. Clean up and discard any material that has fallen though the bed.3. Use a poking tool to free all of the material stuck in the honeycomb. Clean up and discard ma...

1. Reserve each laser one at a time to ensure they're not both down at the same time. 2. Remove the blower from the system and loosen any large debris on the slots on the blower cage with a flathead screwdriver, then brush clean with a bristle brush. Be carefu...

This needs to be reviewed for content and tech_ready suitability before it is approved to be scheduled maintenance Remove the bed and clean up the material that has fallen though. Use a poking tool to free all of the material stuck in the honeycomb. Acqui...

Test the PH of the water Locate the PH test strips, in the computer cubby hole at the CNC Plasma Computer station.   Use a stick or other object to lightly stir the water in the table. Just lightly move the water in between the slats, careful not to splash...

* Remove the battery* Clean the undercarriage using a putty knife and wire brush* Reattach the battery

Service manual: PENDING*Inspect the Blade*Inspect the saw blade for wear and damage.1. If any teeth are missing, yellow tag the tool in a tool report and file a purchase request if there are no spares in the maintenance room.1. If two consecutive teeth are mis...

*Safety* - Wear a dust mask. (If you do not have your own, disposable masks are available in the custodial room.)- Wear safety glasses. *Tools/Materials Required* - Two 2-gal buckets (should be located near the machine)- Soft mallet. *Clean Siphon Tube* 1...