Search Results

*Wash Sink and Water Fountain*Remove and discard any debris from the sink.Wash both sections of the sink and the top surface of the water fountain with soapy water. If Barkeep's friend or other stainless steel cleaner is available, follow the directions on the...

*Empty the Media Seperator Drawer*To the right of the pedestal grinders is a big gray box that is the media separator. There is a cabinet door on the bottom with retaining latches. 1. Put on a dust mask and safety glasses2. Ensure the separator is off3. Check ...

*Clean Out the Pitcher*1. Remove the lid. 2. Wash and dry the lid.3. Remove the top reservoir.4. Remove the filter from the top reservoir and discard.5. Wash and dry the top reservoir.6. Wash and dry the pitcher.*Replace the Filter*Observe the filter replaceme...

*Task List*- Clean the machine with a shop vac and dry cloth.- Wax the cast iron surface of the table- Spray a light amount of teflon lubricant on the support pillars- Check the motor drive belt for wear, splits and cuts. If the drive belt is in poor shape, su...

*Service Fume Extractor Filter*1. Check the filter gauge at the base of the machine.2. if the gauge indicates replacement is needed, fetch (or purchase request) a new one and swap the old one out.- Purchase request: https://protohaven.org/purchasing

Prolonged use of the product when the ink level is below the line on the tank could damage the printer.* Verify on the front of the machine that the ink tank levels are not below the minimum marking. If they are, file a tool report.- Tool report: https://airta...

*Safety*- Wear a dust mask. (If you do not have your own, disposable masks are available in the custodial room.)- Wear safety glasses.- Wear hearing protection.- Wear gloves when handling chips.*Clean Tormach*1. Vacuum out the ways and the chip tray using the ...

*Test Emergency Lighting*Turn off breaker 13 in panel A. (This breaker powers the emergency lighting.) With the breaker off, confirm emergency lights are working in the following areas:- by the bathrooms- in the studio / front half of the building- in the wood...

Clean the Interior Open the side panel. Dredge out any buildup of chips, gunk, and other debris. Ensure the cutting fluid can make its way to the sight glass on the bottom right of the machine. If it's not visible, submit a maintenance request so a traine...

Safety: Ensure the machine is turned off and unplugged before oiling the rollers.  Oil the rollers Apply several drops of 3-in-1 oil (located in the maintenance cart) to the three large rollers of the slip roll. Most of the oil ports will be small holes tow...

Maintenance Automation The pages in this book (as well as the ones in Maintenance - Training Required and Maintenance - Admin Required) are used by software automation to periodically schedule tasks in the Shop & Maintenance Tasks Asana project.  Scheduling ...

The coolant system on the tormach has a tank and a filter screen on it - these should be inspected and cleaned regularly so the coolant can properly flow.*Gather Materials*- 2 Buckets, can be found past the Tormach. One 5 gallon and one smaller bucket that has...

* Woodshop* In the woodshop free bin and the free board caddy in the lathe area, remove any wood that: - Is painted or treated- Has nails/metal inside- Is heavily splintered- Is "swiss-cheesed" with little material to use, etc. *Metalshop* In the metalshop...

*Safety* - Wear a dust mask.- Wear safety glasses.- Unplug all electrical equipment before cleaning. *Task List* With a dry cloth, wipe down all external surfaces of the sheet metal tools:  - shear- slip roller- finger brake- shrinker/stretcher- turret pun...

Sharp metal debris can accumulate in our parking lot - this poses a hazard to car tires, so it's important to periodically pick up metallic sharp objects using our magnet roller. Retrieve the magnet roller, usually located near the recycling bin by the forg...

Perform weekly maintenance Remove the lower panel on the infeed side of the machine. Vacuum dust buildup from inside cabinet and off motor. Check v-belts for damage, tension, and wear. Yellow/Red tag the machine if issues are observed.  Check for problema...

Service manual: PENDING*Inspect the Blade*Inspect the saw blade for wear and damage.1. If any teeth are missing, yellow tag the tool in a tool report and file a purchase request if there are no spares in the maintenance room.1. If two consecutive teeth are mis...

*Materials*For a disinfectant, you can use sanitizing spray (kept under the kitchen sink, with refills in the maintenance closet)Apply disinfectant, wait three minutes, then wipe with a clean cloth or paper towel.If we are out of disindectant, submit a purchas...

*Compare Online and Physical Tool States*1. Open https://api.protohaven.org/techs 2. Make a note of tools in a yellow or red state.3. Visit each of the tools listed as red or yellow state and verify that there is a physical tag on the tool that matches that st...

*Recharge Desiccant Pack* 1. Remove the white rectangular plastic desiccant pack from the "free filament" tote box by the 3D printing cabinet.2. Inspect the desiccant beads through the front window.3. Use the legend by the window to gauge if the beads are wet...